Costo tasto accensione iphone 5 s
Contents:Being mindful of the balance of force is what makes the removal successful. I can confirm with con mar 4. The adhesive was pretty firmly holding my battery down. So I used a metal screwdriver to help leverage the battery out from the top of the battery. Not knowing that the ribbon for the volume button and switch from the left side of the phone were under there. I severed the ribbon and now those buttons don't work anymore.
But I was able to replace the battery and everything else works fine. I just have to learn how to live without those buttons anymore There is nothing you can really hurt on the left middle side either so I recommend this way if your plastic tab does not work to pull the battery up. I couldn't pull the battery out after pulling on that tab for over 10 minutes. I used a knife on the left side where it seemed nothing was and luckily the battery slid right out no problem. Try heating the phone at the back where the battery is with a heat gun or hair dryer what I used and then pull the tab, and if you still can't get the battery to start coming of give it a little nudge with a prying tool at the top.
The battery was really glued down tight, and pulling the plastic tab eventually ripped the tab off and I could no longer use it. After 15 minutes of gently lifting with the plastic opening tool and getting nowhere, I followed the suggestion about using a hair dryer to soften the glue. I blew heat on the back of the phone where the battery is for about 30 seconds, and then used the plastic tool on the side of the phone with the volume buttons, and it lifted out with very little resistance.
I want to stress that it was not a ton of heat--I held the phone in my hand while using the hair dryer, and it was hot on my hand but never so hot that it burned me. The point isn't to cook the phone, just to warm up the glue so it gives a little. Well, the battery was really giving me problems when trying to remove it. I had no chance just using the plastic tag so I had to pry it loose. I would not recommend prying the upper side of the battery as shown in the pictures due to the audio control and power button cable running just under the upper edge of the battery. I was not aware of this cable and ended up damaging it when the plastic removal tool slipped under the cable when prying.
I believe this cable supplies power to the vibrator as well since that's what ended up not working when everything was back in its place. Fortunately this cable can be replaced but it looks like a bit of a hassle but i'll try. Try using the hair dryer before prying too much would be my recommendation. I put a bowl of water in the microwave with a plate on top. Once the plate was mildly hot, I took it out and placed my iphone on it to heat up the adhesive. I tried pulling the plastic tab, but nothing would happen. I noticed that there is an ideal prying point on the opposite side of the battery from the plastic tab an inch below the volume buttons.
There are no ribbon cables or circuits there, and there is a cutout large enough to fit the plastic pry tool. Pry gently there against the case once the phone is warmed up on the plate and the battery comes out very easily. It really seems like that cutout is there just for that reason. The word "pry" should not appear anywhere in the this section as the damage others have experienced witness. LIFT instead with the end of the tool.
It would have been helpful if the notes for step 16 prying out the battery had mentioned that the Audio Control and Power Button Cable is fragile and behind the top of the battery! I was gently prying out my battery from the top when I tore the power button ribbon that I could not see.
This step is the toughest one. My old battery glued on the board stubbornly and refuses to come out. It took me half hour or so to pry it out. It has deformed and way beyond usable state. The key here is to pry from all allowed angles refer to the pictures and video , and pry patiently. Mine starts to come out after prying from the top. When prying the battery off at the first battery position shown in the picture the gap between battery socket the battery itself , a small rounded metal spudger like the one that comes with the iFixit Pro Tech Toolkit is recommended if you break your plastic prying tool like happens to me during this step.
Just make sure that when prying up, you are not touching either the battery socket nor any other logic board component. I also recommend to use a tool like the iOpener and put it on top of the battery for few minutes to reheat the battery and soften the battery adhesive during this step. I used the plastic tab, but it broke off.
I was forced to pry it out, but like I said, it didn't come out easily and the battery was all mangled by the time I pulled it free from the adhesive. This guide tells you where to pull and where to be careful, but it still made me very nervous! Just keep working at it if yours is also stubborn.
I would suggest using both the clear tab and the plastic opening tool simultaneously to be able to remove the battery. Easy does it on this step. The adhesive is very strong. I though my battery wasn't going to come out. But even prying from all three indicated locations does it eventually. I was able to remove the battery after applying the iOpener twice for about 10 minutes. I pulled at the plastic tab and used the plastic opening toll together.
The battery lifted while applying permanent strong force. I followed this advice above: I did not have to use any other prying point. The battery was fixed with one drop of glues and with tape sticky on both sides. In fase di rimontaggio, assicurati che la batteria sia fermamente appoggiata al case posteriore. In questo modi si eviterà ogni danno agli altri componenti nel rimontare il pannello anteriore.. Esegui un hard reset dopo il rimontaggio.
Questo evita diversi inconvenienti e semplifica la risoluzione dei problemi. I have removed the battery in many iphone 5 phones to repair other issues and never had a problem with reusing the battery. Hello from Cyprus there Anyway i listen the sound when the phone open or change Any help to get reed of it? I can't recommend changing the battery, I did everything as shown but my iPhone doesn't work anymore. If I connect it to itunes it wants it to restore and when I do that. It sets itself back in recovery mode.
I did not break anything and used only plastic tools to remove the parts. Even after I put the old battery back in it still shows the "connect to iTunes". Hi, I thought that when I prised the battery out, I'd knocked 2 chips off the logic board, chances are this is what's happened to you too They need to change this tutorial to use the plastic tab to remove the battery as I've seen several people with this issue. The only way to fix this is to get 2 jumpers soldered onto the logic board.
Any luck finding a solution to this? I replaced my battery and the repair went relatively smoothly Any advice would be greatly appreciated. Don't completely peel away the plastic from the base of the phone. The plastic has a mechanical but not electrical purpose and should not be removed. The step directions make it seem that you can peel away the plastic, but don't do that. Peel and pry the battery out but leave the plastic in place. I made this mistake and Apple wouldn't repair my iPhone because the plastic was missing. The guy said that the plastic holds the circuitry in place and away from the battery.
Do not remove the plastic. My iphone 5 keeps switching from vibrate to ring randomly on its own. Do you think this would solve the problem". Well, I followed all the instructions I followed all the instructions and when I put it back together, all I get are white lines on the screen. After replacing my battery on iPhone 5, my GPS was shotty and couldn't pinpoint my exact location.
Opened it back up and realized that that longer thiner cable running the length of the battery on the circuit board side wasn't clipped in its spot. Be careful to make sure your replacement battery gets put in the case seated at the bottom, if not when you close up the front facing camera will be on the battery and if you force it not realizing you will damage the front camera.
The first time I put the phone back together, I turned it on but had a black screen. I took it back apart and put it back together again, same thing. I thought that I must had torn something but kept tinkering with it. I discovered that some of the foam adhesive strip that goes on top of one of the wiring harnesses that snaps the screen back to the phone had come off and was actually on the receiving side of the wiring connector bracket probably not using proper terms here. I used the plastic tool that came with the kit and removed it I was careful not to touch with my fingers for fear or oil getting on the harness.
Tried again still nothing.. I thought I had heard it click before, but I really looked at this time and realized I had to turn it slightly inward to get it perfectly straight, and then it clicked. Hope this helps someone. I have done everything correct, but I have 2 problems, the power button and the home button is not working anymore. The recovery mode problem as ive found so far is unfixable apple geeks said its toast as well as att.
Ive tryed redsn0w and tinyumbrella to kick it out of recovery mode and it does but restarts right back into it. Itunes fails to update or restore. This is a significant risk to be sure, i had no problems changing the battery no clips broken no unnecessary prying and its well powered brick now. I thought I'd done something wrong because my phone would not turn on I finally charged it overnight and then did a hard restart holding the power button and home button at the same time and it worked!
- software spia telefono cellulare?
- spiare il cellulare del partner è reato.
- come spiare telefono iphone.
- come spiare il cellulare di un amico;
- configurazione network dati cellulare iphone tre!
- come capire se iphone 7 originale.
I have no experience doing this sort of thing and it was a little intimidating, but the video really helped, and it was manageable I thought I did everything correctly but my phone didn't power on as I thought it should. I went back and double checked that everything was connected correctly which I hope it is and I didn't damage anything in the process I figure maybe the battery has to charge but usually once it plugs in after a few minutes it shows that its charging and in this case it is not charging. Also, I received a liberation kit with a small piece on it.
Can you tell what this is for? Tab broke pretty easy and a hair dryer did nothing. I put a plat in the microwave with a large bowl of water under it. Heated it till I could barely touch it and then laid the phone on it. Make sure the plate is big enough for the whole back of the phone to touch it. Leave it on a few minutes and the phone should get pretty hot but still touchable.
Patience is a huge virtue on this step. I can't get the new battery connector to snap into the port. This doesn't seem to be mentioned as a problem step for other people. When you install the new battery, if the compartment is a bit larger than the battery, push the battery over to the side wall and leave about 1mm space between the battery and the electronics.
This will give you more room to place the battery cable with the proper twist. By the way, it's easier if you first plug the battery connector into the board on the phone and THEN position the battery into the battery compartment. This way you'll have the greatest degree of freedom to position the connector for proper insertion. Have followed all instructions and was careful and I think everything is intact but on trying to charge am not getting anything. Will try leaving it plugged in to charge overnight as per someone's suggestion above.
Usare la punta di uno spudger per fare leva sul cavo connettore e portarlo su sulla logic board, un poco sopra allo speaker. The dock connector flex cable can be slid under the board wihtout removing it. I just did it myself without a problem. Agreed - steps can be skipped if one is just replacing the speaker. I completed mine today with these very helpful pictures and descriptions. I also think you can probably skip removing the battery altogether - I removed it just to be safe, but do not think it was necessary. That said, removing the battery gave me more room to work with or seemed to, at least.
For replacing the dock connector, there is no need to remove the logic board! Just skip the corresponding steps. Removing the battery or disconnecting the display is strictly speaking not necessary either. However, I would strongly recommend to do so for convenience.
This tear down and these comments were my lesson to read ahead here. My phone has been in pieces because I do not have the finger to get the antenna cable back on. Rimuovere le due seguenti viti che fissano il supporto superiore della logic board al corpo del cellulare. State attenti a non rompere la piccola linguetta di messa a terra vicino alla parte posteriore della telecamera. Nei modelli piu moderni il supporto potrebbe essere fissato alla telecamera e non poter essere estratto completamente.
Se debe retirar con cuidado , para luego utilizar la misma platina en la nueva camara de reemplazo. Je fajn, ze tu pises vo svojej reci, tak isto ako ja. Rozumiet ti bude presne tolko ludi co mne, tak nabuduce tu pis v anglictine a neotravuj ostatnych svojou domorodou skomoleninou. My phone had the bracket attached to the camera and snapped off. When I put everything back together my bottom mic stopped working.
Could this top logic board bracket not being attached anymore cause this? What if I broke the tiny grounding tab next to the rear camera that he warns against? Is it possible to find this replacement part? Second Connector - From the top right corner of the connector lift straight up. It will go to the left. Third Connector - Hold the second cable back and again lift from the top right corner of the connector and it will go to the left.
Strangely, after reassembling the device I cannot find any malfunction. I wonder what the connector is for…. Yes you have to remove battery first otherwise it may cause a short circuit sometimes. What exactly do wedisconnect? This is not adishnetwork? I have a problem. What is this used for? I broke the one at the left because the screw was impossible to remove I was unable to remove the screw on the left. Consequently, I ended up tearing the cable right where it is attached to the left screw, but as far as I can tell, everything on my iPhone is working properly.
Whey did we take these screws out? Removal doesn't seem a pre-requisite for any other steps. In trying to put the phone back together, I can't get these screws back in - they don't seem to grab. But I also have this miscellaneous part that I don't know where it came from - it has one hole in the center and looks a bit like a wing.
Anyone know what this is and whether it has anything to do with these two screws? OK, I got the screws back in, but it still looks like an unnecessary step. And I still have that little wing thing. But the phone is working and charging! These screws secure some thin cables with contacts on the end of the logic board. Some here states they are hard to remove. I used one of my Philips screw drivers. I'm not sure what type, but it removed the two screws easily. In the years that have past, doing repairs, I have got a lot of different equipments.
Panoramica Video
Just be sure to use exatly the right screwdriver. Rimuovi la singola vite Phillips da 1,2 mm rimasta nel supporto della zona centrale della logic board. When putting this back together, you may find this bracket gets in the way of clipping the battery connection back on. If you do, losses the screw and swivel the bracket out of the way. When I did this the ribbon cable beneath the plate stuck to the plate, and this guide makes no mention of this cable at all.
Be aware that it has to be re routed and re attached to its positions on the logic board or your phone will not work, as i looks like some kind of RF cable. That cable is for sim networks. You have to remove very carefully. Usare uno spudger per fare leva sul cavo connettore del Lightning connector e staccarlo dalla logic board. Premere il bottone per liberare la carta SIM sul lato destro dell'iPhone con il "SIM card eject tool" o con una spilla da balia piegata.
Queste viti sono dello stesso tipo di quelle Phillips, ma noi vi consigliamo di usare un cacciavite a punta piatta da 2. Assicurati di rimettere questo distanziale filettato nella sua posizione originale nella parte superiore della logic board. Un elemento magnetizzato potrebbe interferire con la bussola elettronica.
Suggerimento per il riassemblaggio: Before continuing to step 24, ifixit forgot one step!! Using a flathead driver for the standoff screws is actually very irritating. Funny thing, if you just use the pentalobe driver you used to take out the first two screws for the iphone, the standoff screws come out very easily I think this was by design, since the pentalobe driver fits snuggly into the opening of the standoff screw. It is not equivalent to the remaining two 2.
It should be kept apart and put back in its exact place. If you happen to mix it with the other 2 screws, it is easy to differentiate: The center hole is threaded to receive other screws. If you look at the previous steps, you can see the screws that screw into each one. Without that tool, the best alternate is a flathead. I would avoid using a bit in the center hole, since it may damage the threads. The flate heat second from the biggest fit in the slots good enough. The little bastards are on there tight!! I used a 2mm flathead, but I had to be very carefully because it may be easy to slip.
A little sad that I don't have any flathead tips and missed that they were needed! Anyhow to make this standout even more? I have the iOpener with a decent assortment of tips so my overconfidence made me miss the requirement. My spudger tip broke-off inside one of the standoff screws, so after trying a few things to clear the plastic tip manually, I just took the standoff screw out and held it up to open flame. The tiny bit of plastic burned-away in no time at all and after cooling the standoff screw down, it worked just fine again: Non provate ancora a rimuovere completamente la logic board dal pannello posteriore poiché vi é ancora un cavo connesso alla parte inferiore di quest'ultima.
Il flash surround è attaccato alla flash unit ed al pannello posteriore. Se resta sul pannello posteriore rimuovetelo con delle pinzette e rimontatelo sulla flash unit. I second John Mihalko's comment - when reassembling the logic board in the case, make sure the button assembly cable from step 18 is not under the logic board. It was a bit annoying to almost get to the end of this repair only to find I had to go back and take the logic board back out again.
I've had to open this phone twice at distant intervals and I made this mistake both times. This should be included as a note, because it seems to be a common error. I thought I already remove it but it turns out I only remove the top screw. There's actually "another" screw in the "same" position, which is in disguise because it looks like a hole. It needs a rather small flat screw head to remove. I kept pulling the circuit board out but couldn't because I didn't know it.
Lors du remontage il faut être vigilant à ce que le câble d'interconnexion inférieur ET!!! Usate l'estremità di uno spudger per fare leva sul cavo dell'antenna del Wi-Fi e sollevarlo dalla parte inferiore della logic board. I didn't bother taking the antenna cable off the board. I just had it flexed back and worked on removing the camera with the cable still on. It's only two screws and one connector to swap the camera out.
Found it a little fiddly disconnecting it so if you have trouble just leave it on and work with the slack. Mentre la vostra logic board é fuori dal telefono tenetela messa a terra per evitare danni al circuito. I believe there are three washers on the case side of the logic board that can come loose at this point. A note when putting it back together make sure that the antenna cable does not get stuck under the logic board.
Guys, there is no need to remove the logic board at all. Just disconnect battery, remove loudspeaker, and remove charge port. Usa la punta della spatola per rimuovere il paraurti di gomma dal basso della pulsante dell'alimentazione. You do not need to remove the rubber bumper.
I did the replacement without removing it and that works just fine. I agree with Johnny on Step 31, removing the rubber bumper is pointless as once its removed you end up with a floating rubber bumper piece OR to replace it. The rubber bumper pretty sure its just foam anyways is fine staying attached as it is. Other than that the guide is spot on! Rimuovi i seguenti viti del supporto metallico tra il flash posteriore e la finestra della camera:.
If you only take off the top screw on this bracket and just loosen the bottom one you can spin the bracket out of the way. This helps you when putting everything back together. YOu don't have to align this little bracket while holding a screw and screwdriver. I had an interesting discovery when I got to this step. Mine was more of a circle. It's like it was stripped already.
My magnifying glass is not great so I couldn't see if it was stripped or if a different bit was needed. I ended up leaving it in and just swinging the bracket to the right just as the5dunhams suggested. Thankfully it worked and I was able to continue on my 4. It's weird using my power button since it's been broken for a couple years. Usa la punta della spatola per svoltare il supporto metallico chi tiene la pulsante dell'alimentazione dalla testa della faccia posteriore. Premi la pulsante dell'alimentazione nella faccia posteriore dal'esterno del telefono con la punta della spatola.
There's a metal 'hinge' on one side of the power button. When reseating this has to face upwards side of the screen else it wont click. The power button is glued on the right side to a piece of foam. Re-assembly should be easier and quicker this way.
Sostituzione del pulsante di accensione in un iPhone 5 - Guida di riparazione iFixit
I found these instructions on the internet, and it worked for me - many replacement housing seem to lack that pin. I accidentally got the black power button instead of the white one for my white iPhone 5 and the button doesn't click like it should. I wonder if there is a difference in size of the white button vs. I only replaced the button, but I may replace the cable to see if that makes a difference.
The button now is not working as well as it did first. I replaced the cable with the power switch AND put everything in a replacement housing. My power button clicks and works fine, but it a bit loose, so as if there is about 0. In the original state from the factory, the button sits tight. I successfully replace my power button, and it worked fine for about two weeks, but the responsiveness of the button has gradually become worse.
I'm wondering if this means I need to also replace the cable. Any help or advice would be greatly appreciated.
Ti trovi qui
Altre persone hanno completato questa guida. Tobias Isakeit ci sta aiutando ad aggiustare il mondo! Great step by step guide. I did it twice today and my iphones 5 are working great. In my opinion there is no need to remove the battery. It is how I did it without any complication. This is an extremely helpful guide. I was quite surprised when I opened my iPhone 5 that there were 2 screws lose inside it. I bought it new and have never taken it apart or had it serviced before. Never heard any rattling either so who knows. I noticed that needed the smaller Phillips head screwdriver than the one recommended in the guide.
The only advice I can give is to take your time and go slow slow slow. There were many small heart attacks when prying the screen off and taking out the battery. I had to go considerably farther in taking apart the phone. My lock button was attached to the volume, mute, and vibrate as one band. I was skeptical that replacing the tiny power button alone would fix my issue of turning my phone on and off and putting it to sleep, but it did the trick to my great surprise.
- software intercettare whatsapp.
- Trova i prezzi più bassi per tasto accensione iphone su turisticnakmetijaslemensek.si.
- Riparazione Tasto Accensione.
- spiare un cellulare yahoo!
- spiare stato online whatsapp.
- come verificare autenticità iphone 8 Plus!
- Sostituzione del pulsante di accensione in un iPhone 5?
You'll need a steady hand ie. Thanks iFixit for a great guide! My volume and silent toggle switch works great but I'm having issues only with the power button. Does this mean I just have to replace the power button or do I have to replace the flex cable also? This is the best on the net but the video leaves some steps out.
It would be good to tell people to refer to the steps below. I assumed everything below the video was ads so I didn't look there unit I realized something was missing. After watching this video I ordered my parts and planned to do this. Once I got the phone apart i realized that my button problem where it works but you have to push hard wasn't going to get fixed by this video. The button that this video replaces is just a mechanical block.
Tasto accensione difettoso iPhone 5, programma straordinario di riparazione
For me, I just cleaned everything the best I could don't forget to clean the camera and lens over the camera while you are in there and put it back together. Everything works great now. No new parts were needed - just a cleaning. Somebody had some problem with audio jack after this guide? Because mine apparently stop to work after the sostitution!! And I don't understand why.. I didn't touch any other part, infact the charging component and the speaker are working good!
I followed the guide exactly, including putting the logic board in an anti static bag. Afterwards the iPhone 5 wont turn on, just a blank screen. When connected to power it makes a loud beep, and pauses for several seconds and beeps again etc. I back tracked and did it all over double checking every connector.
Checking the display connector. What could it be? I had that too. You need to make sure to turn off your power when doing any repairs. After a week I checked back and my phone started working again. I repaired the power switch problem by just cleaning it. I did not remove the battery or camera, but did remove the small metal bracket just below the power button. I carefully used a contact cleaner spray and small knife to clean out some dust. I didn't turn my iPhone off before taking the display assembly apart.
How will this affect my iphone? I replaced the button just fine, and I also did not need to remove the battery. I noticed though that there is a little pin that holds the button back that was also broken on my phone or fell out that I had to get on ebay. I'm in the process of changing the rear housing for my 5s, and I've come to a problem with the lock button. Can i take it out of the previous housing, or can i buy a new one for the new housing? What should i do? Try not to bend the pin. Pin was then straightened slightly with flat pliers and re-slotted into the new case, keeping the 'fat' end at the top it will need forcing home slightly.
Took a few goes to get the clip back but wake button clicked fine. I also replaced the volume control buttons, specifically because the volume down button didn't work, but the problem persists even with the new volume control buttons and new cable assembly. I suspect that it's not a hardware problem, but I haven't found a software fix. Tried everything I could think of, even a full factory restore, still doesn't work. As a workaround I use the system setting that displays a moveable touch control that allows volume to be changed:. This displays a finger-tip dot that you can move anywhere on screen.
Touching the dot displays 6 icons, touch "Device" then there are more icons including "Volume Up" and "Volume Down", which do work. Of course this problem first appeared soon after my AppleCare expired. Followed this and it worked for the most part but now my phone does not charge. If I insert the power cord while the phone is turned off it will boot the phone up but does not actually charge the phone. What could have gone wrong? The cable isn't an official apple one but was working before the repair. Did you resolve the problem you were having with battery not charging?
I am having the same problem, everything worked fine after the replacement and just found out that the battery won't charge the lightning connector when connected does not get detected. There is a plastic cord which runs around the glass, half of which remained with the glass, and the other half remaining on the remaining part of the display assembly. I'm not sure what I did wrong for this to happen. But I can't put the phone back together. In any case, the power button now does not click. And floating bits of what I assume used to be a button a small silver bubble, and a black dot on a piece of clear plastic came out when I removed the the power button.
I tried fixing the power button, but it doesn't click. It sits very soft on the top I can't figure out anything missing. When i reassembled and plugged in, phone just keeps flashing apple symbol but doesn't turn on at all. This could be due to the fact that power button is not clicking I thought of replacing the whole ribbon, ordered and tried installing. I had thought that circuit button that connects to the power button had worn out, so decided to change so that power button would click.
It doesn't click now. I am stuck, now I am thinking of resorting to some fix by the pros I wouldn't suggest anyone trying this. The whole thing needs to be replaced, since the flex cable includes volume and the rocker components. This is a poor guide because it is misleading. The steps are well done, but you need to include the steps for removing the volume flex parts as well.
I had to remove the power cable assembly as well, but by that time, it was pretty obvious which extra screws to remove. The detailed pictures helped me get it right. Worth noting that sometimes the power button can start failing for a reason that has nothing to do with the button or its cable. Mine started failing because the battery was puffing up, pulling the button connections further and further apart. Once you've got the phone open it's easy to see that the battery is pillowy.
Before you open the phone you may see a vertical faint bluish stripe down the screen, or note that the case looks very slightly sprung. The solution to all these problems is to replace the battery. Before you buy parts you don't need, see if your battery is the culprit. I tried this last night and it worked, brilliant i thought then realised that i have lost my carrier and signal has gone on the phone, i have tried all aspects of the internet, turn off, take sim card out and reboot network, still nothing. Done successfully for two phones.
The standoff screws were a pain. To remove them I used a sharp knife placed flat into the groove on the screw and unscrewed a quarter turn at a time. The iFixit screwdrivers are not fine enough for that. To reassemble, I held the standoff screws in position with tweezers and rotated the phone underneath it. I used several guides simultaneously as there are many details to check and double check. Together we can do anything! We have a chance to guarantee our right to repair electronic equipment—like smartphones, computers, and even farm equipment.
This is a once-in-a-generation chance to protect local repair jobs—the corner mom-and-pop repair shops that keep getting squeezed out by manufacturers. Join the cause and tell your state representative to support Right to Repair. Tell them you believe repair should be fair, affordable, and accessible. Stand up for your right to repair! Aiuta a Tradurre iFixit. Sostituzione del pulsante di accensione in un iPhone 5 Scritto Da: Andrew Optimus Goldberg e 15 altri collaboratori. Tempo Necessario Suggerisci un tempo?? Introduzione Usate questa guida per rimuovere il pulsante di accensione dal vostro iPhone 5.
Strumenti Acquista questi strumenti. Parti Acquista questi componenti. Passo 1 Modulo Display. To avoid broken screens during reassembling: Hi every one i drop my iphone5s 16gb I replace 10! So, i decided to open it up again and reseat the ribbon cables in case they came loose. Wish I ordered a back case as well with my repair being so easy! I'm experiencing the same issue.
Were you able to fix it? Please let me know. Please contact me asap re: Passo 3 iSclack Opening Procedure. Was someone able to answer this question? I have the same issue. I think that's not a good idea as the top of the display is held in place with plastic tabs. If you apply to much force they can break. I took the suction cup off of an old navigation Tom Tom and it worked great! The suction cup didn't work, because of my destroyed front glass.
So i take "tesa powers trips". With that help, i had enough force to pull up the front display from the rear case. Where can you buy "Tesa Powerstrips? I broke the front glass with this technique.. Thank you so much! My front panel flew right off after some puling on the suction cup - no prying was necessary. Fortunately, no cables got damaged. I can confirm, the Garmin sucker cup worked like a charm. Within 5 seconds it popped open.
Need extra careful while pulling the screen. Once the bottom part is free, the screen will pop out easily. Use needle its a best way. I could never even get the case open. The suction cup will hold if you put a piece of tape over the cracked screen. Suction cup does not work. I also had to use the Garmin suction cup. In the end everything was fine and phone works great. But remember to be super careful.
I hope it helps! Worth adding to the main tutorial that the screen re-install must start from the top. The compass is right next to it. Mes difficultés étaient de remettre les petites vis aimantés, difficiles à remettre! Patrick Rosa, june 23 The non-magnetized screw was very difficult to install. This is how I ultimately succeeded: One of the screw is completely stuck and I cannot remove it! What can I do? What an idea, lol. Thanks for any insight in advance. There is also a new brighter spot on the screen.
The comments are usefull too. If your lcd is properly fine then it can be a LCD Ic issue on pcb. Also, when the battery was too low and before the display produced vertical lines the display showed half of a low battery symbol: Like the right side of the display was blank. O iTunes asked me to update the iOS to What is my problem, please help: Try replacing the camera and flex assembly.
Passo 13 Alzare la batteria. I didn't need to remove the battery to complete the steps after. The hair dryer trick on the back of the iPhone did it for me. Passo 14 Uso dell'iOpener.
Passo 15 Distacco della batteria. I use credit card and put wider side to pry battery this make batter not deform easily. Prying from the volume side will also reduce the chance that you dislodge the GPS connector. Wish I'd read your comment before I did this step!
I think it is needless to remove the battery at this stepp. I have remove the battery at last. Love how the battery changed to an iFixit branded battery, in the phone!!!! How about using a suction cup on the battery, along with a pry tool? Passo 16 Rimozione della batteria. Even after I put the old battery back in it still shows the "connect to iTunes" Does anyone have an idea what to do? Have the same problem Have you found any solutions? Thanks for the suggestion.
I went ahead and added a warning on step I have the same problem. Passo 17 Gruppo Logic Board. Stages need to be removed from this guide!!! The cable slides out easily. Actually, you can skip and -- I found the others to be necessary. De toda la guía en nuestro caso , este fue el paso mas engorroso. Superado esto todo fué normal. Perdimos 2 tornillos de esta guía: Un tornillo de la platina en el paso 17 Otro tornillo en el paso 10, el tornillo central que asegura las 2 platinas.
This is important and left out. First Connector - Lift from the top of the phone to the bottom. Exact same thing happened to me. Tested every function of the phone and nothing seems broken. I had to remove the battery to get the correct angle for these screws. That is gps antenna. Turns out this is the GPS antenna. I just watched the video and this step wasn't included. So why is it here? What are these two cords are for? I broke one on the right because, I couldnt open the screw. Those 2 cords are for GPS antenna to send and retrieve signals.
In my opinion spudger form the left side lifting to the right. I use the 1,5mm ifixit - works great! I made that mistake too. None of your buttons will work if it's tucked under. Passo 30 Sostituzione del pulsante di accensione in un iPhone 5. Seems to be missing a step to remove the screw from the plate that holds the power button in. I don't think you really need to remove this rubber bumper.
Is this the rear microphone between the rear camera and the flash LED? I lost the One 2. The screw on the left side had to be removed, but I believe these guides are skipping that step. Do you mean the screw which is removed on step 32 picture two? Step 35 picture Did you also replace the cable or just the button?
You need to replace the cable. Per riassemblare il telefono, seguite le istruzioni nell'ordine inverso. Un ringraziamento speciale a questi traduttori: Autore con 15 altri collaboratori. Andrew Optimus Goldberg Membro da: It's highly recommended to replace the cable. What did you clean it with? The power button now has the 'click feel' again and powers the phone on and off. I tried this today for the second time, Power button won't come back up.
I think the metal bracket, holding the button up, is broken or bent, I forced it a little. But I can't find this part nowhere online.. Hi, did you finally find that part? As a workaround I use the system setting that displays a moveable touch control that allows volume to be changed: Need to make sure the cable you received is not defective.
HI Michael, Did you resolve the problem you were having with battery not charging? Hello, I have exactly the same problem, did you find any solution? Thank you very much. Non ci sono commenti dei clienti per il momento. Solo gli utenti registrati possono inserire un nuovo commento. Offerte In questo momento non ci sono offerte.
Newsletter Accetto i termini di privacy Iscriviti Cancellati Accetto i termini di privacy. Sostituzione connettori di ricarica, jack audio Riparazione iphone 7 Plus Recupero Dati Smartphone e Recupero dati Smartphone Tablet Android Sostituzioni e Riparazioni di lettori e Eseguiamo riparazioni su schede madri come Home Chi siamo Laboratorio Team Contatti Mappa Pagamenti e spedizioni Termini e condizioni d'uso Questo sito utilizza cookie tecnici e di profilazione, propri e di terze parti, al fine di fornirti una migliore esperienza di navigazione, per scopi pubblicitari o anche solo per fini statistici.